LED downlights are products developed on the basis of traditional downlights using new LED lighting sources. Compared with traditional downlights, lamps have the following advantages: energy saving, low carbon, long life, good color rendering, and fast response speed. The planning of LED downlights becomes more beautiful and lighter. When installed, the overall unity and perfection of the building decoration can be adhered to, and the setting of the lamps is not damaged. The light source is hidden inside the building decoration, the light source is not exposed, no glare, and the human visual effect is soft and uniform. . Now more and more people are inclined to choose such lights, but do you know how to install led downlights?
How to install the LED downlight? How to remove the LED downlight?
1. Connect the red or yellow line of the LED downlight to the front of the ceiling, and connect the zero line to the zero line.
2. If it is a 1.5 power cord, the insulation is broken by 1-2 cm, and the standard connection method is hinged (two strands are evenly hinged together in a straight line), and then surrounded by insulating tape, and the surrounding is required to exceed the leakage screw. 1/3 of the line length.
3. After twisting the wire, leave your hands and turn on the power to confirm that the contact is connected.
Downlight is a type of lighting fixture that is embedded in the ceiling and emits light. There is a spring buckle on each end, just take it off. Downlights generally have a screw base, which can be directly mounted on incandescent lamps or energy-saving lamps. If the LED downlight is used for a long time, it must be replaced and repaired. The following is the replacement and repair method of the LED downlight.
1. Prepare the things needed for replacement and repair of led downlights. Generally, common things for replacing and repairing led downlights are: electric tape, a set of LED downlights of the same model, pliers, and a small hand saw if necessary.
2. Turn off the power first, buckle down the lamp gradually, pay attention to the reed clip on the lamp, hold it down with your fingers when you see it, and then remove the lamp. It hurts, so be careful to disassemble the broken led downlight.
3. Then first disassemble the connector and replace the lamp head. The driver does not move, and the switch is turned on. If the lamp does not light up, it can be determined that the driver is faulty, and the driver must be replaced.
4. At this time, turn off the light switch (for safety), turn off the main power supply, and then unplug the drive's power supply line, then remove the broken drive, and then input the new drive power supply. Peel the ends of the two lamp wires.
5. Wrap one of the driver power cords around the other of the lamp power cords (the lighting power is not positive or negative), stick it with electrical tape, and connect the other one with the same connection method and wrap it with electrical tape.
6. It is about to be completed. Next, power on the experiment and turn on the switch and the light will light up. If it does not light up, repeat the above process. However, this time, instead of replacing the driver, directly replace the led downlight.
How to install the LED downlight? How to remove the LED downlight?
1. Connect the red or yellow line of the LED downlight to the front of the ceiling, and connect the zero line to the zero line.
2. If it is a 1.5 power cord, the insulation is broken by 1-2 cm, and the standard connection method is hinged (two strands are evenly hinged together in a straight line), and then surrounded by insulating tape, and the surrounding is required to exceed the leakage screw. 1/3 of the line length.
3. After twisting the wire, leave your hands and turn on the power to confirm that the contact is connected.
Downlight is a type of lighting fixture that is embedded in the ceiling and emits light. There is a spring buckle on each end, just take it off. Downlights generally have a screw base, which can be directly mounted on incandescent lamps or energy-saving lamps. If the LED downlight is used for a long time, it must be replaced and repaired. The following is the replacement and repair method of the LED downlight.
1. Prepare the things needed for replacement and repair of led downlights. Generally, common things for replacing and repairing led downlights are: electric tape, a set of LED downlights of the same model, pliers, and a small hand saw if necessary.
2. Turn off the power first, buckle down the lamp gradually, pay attention to the reed clip on the lamp, hold it down with your fingers when you see it, and then remove the lamp. It hurts, so be careful to disassemble the broken led downlight.
3. Then first disassemble the connector and replace the lamp head. The driver does not move, and the switch is turned on. If the lamp does not light up, it can be determined that the driver is faulty, and the driver must be replaced.
4. At this time, turn off the light switch (for safety), turn off the main power supply, and then unplug the drive's power supply line, then remove the broken drive, and then input the new drive power supply. Peel the ends of the two lamp wires.
5. Wrap one of the driver power cords around the other of the lamp power cords (the lighting power is not positive or negative), stick it with electrical tape, and connect the other one with the same connection method and wrap it with electrical tape.
6. It is about to be completed. Next, power on the experiment and turn on the switch and the light will light up. If it does not light up, repeat the above process. However, this time, instead of replacing the driver, directly replace the led downlight.